Modification History
Release 3 - Packaging for pathways clarified and choice for Group A corrected. No changes to packaging rules.
Release 2 - One unit title corrected for MSFFM3010. No change in outcomes.
Release 1 - New qualification
Qualification Description
This qualification covers the skills and knowledge required to perform a range of skills at trade-level for those working in furniture making and those involved in the manufacture and installation of fitted furniture typically in a kitchen, bathroom and related context. Installation skills may be applied to new or renovation work. The work is in a defined range of skilled operations, usually within a range of broader related activities involving known routines, methods and procedures, where some discretion and judgement is required in the selection of equipment, services or contingency measures and within known time constraints.
This qualification offers a generic Certificate III in Cabinet Making, as well as two pathways targeting the skill requirements of free-standing furniture makers and kitchen and bathroom cabinet makers and installers.
The following additional qualification descriptors are approved for this qualification:
|
Pathway 1: |
MSF31113 Certificate III in Cabinet Making (Furniture) |
|
Pathway 2: |
MSF31113 Certificate III in Cabinet Making (Kitchens and Bathrooms) |
The MSS30312 Certificate III in Competitive Systems and Practices is available for employees at this level who already possess technical skills and who require additional manufacturing practice skills above those available in this qualification.
Depending on the state and territory where work is undertaken licensing may relate to this qualification where the candidate is required to work on-site assisting in kitchen and bathroom installation. The licensing requirement will usually involve construction induction training. Where licensing is required the unit CPCCOHS1001A Work safely in the construction industry should be selected. If no licensing requirement exists e.g. where all work will be off-site then the unit MSAPMOHS200A Work safely should be selected.
Entry Requirements
Not applicable
Packaging Rules
To be awarded the MSF31113 Certificate III in Cabinet Making, competency must be achieved in twenty-eight (28) units of competency.
- six (6) core units of competency
- twenty-two (22) elective units of competency.
Note: Units marked with an asterisk have one or more prerequisites and must be considered in the total number of units. Please refer to individual units for details.
CORE UNITS
Complete all six (6) units from this list.
|
Unit code |
Unit title |
|
MSAENV272B |
Participate in environmentally sustainable work practices |
|
MSAPMSUP102A |
Communicate in the workplace |
|
MSAPMSUP106A |
Work in a team |
|
MSFFM2001 |
Use furniture making hand and power tools |
|
MSFGN2001 |
Make measurements and calculations |
|
MSFGN3001 |
Read and interpret work documents |
ELECTIVE UNITS
Select twenty-two (22) units from Groups A to F as specified below.
Generic qualification
- a maximum of one (1) unit from Group A
- a minimum of eight (8) units in any combination from Groups B, C or D
- a minimum of eight (8) units from Group E
Pathway 1 – Furniture
a maximum of one (1) unit from Group A
- a minimum of eight (8) units from groups B or D
- a minimum of eight (8) units from Group E
Pathway 2 – Kitchens and Bathrooms
- a maximum of one (1) unit from Group A
- a minimum of eight (8) units from Groups C or D
- and a minimum of eight (8) units from Group E
The balance of units (up to 5) can be chosen from Group F, or from Groups B, C or D.
Group A
|
Unit code |
Unit title |
|
CPCCOHS1001A |
Work safely in the construction industry |
|
MSAPMOHS200A |
Work safely |
Group B
|
Unit code |
Unit title |
|
MSFFF2004 |
Prepare surfaces for finishing |
|
MSFFM2002 |
Assemble furnishing components |
|
MSFFM2005 |
Join solid timber |
|
MSFFM2006 |
Hand make timber joints |
|
MSFFM3002 |
Construct furniture using leg and rail method |
|
MSFFM3005 |
Fabricate custom furniture |
|
MSFFM3006 |
Install furnishing products |
Group C
|
Unit code |
Unit title |
|
MSFKB2001 |
Prepare for cabinet installation |
|
MSFKB3001 |
Identify processes in kitchen and bathroom projects |
|
MSFKB3002 |
Determine requirements for installation of cabinets |
|
MSFKB3003 |
Check and measure fit of cabinets |
|
MSFKB3004 |
Conduct on-site adjustments to cabinets and components |
|
MSFKB3005 |
Fabricate cabinets for the built-in environment |
|
MSFKB3006 |
Install fitted cabinets and components |
Group D
|
Unit code |
Unit title |
|
BSBCUS301B |
Deliver and monitor a service to customers |
|
MSFFM2003 |
Select and apply hardware |
|
MSFFM2010 |
Set up, operate and maintain basic static machines |
|
MSFFM2011 |
Apply manufactured board conversion techniques |
|
MSFFM3010 |
Prepare cutting list from plans and job specifications |
|
MSFFM3021 |
Set up, operate and maintain computer numerically controlled (CNC) sizing machines |
|
MSFFM3022 |
Set up, operate and maintain computer numerically controlled (CNC) machining and processing centres |
|
MSFGN3002 |
Estimate and cost job |
|
MSS402030A |
Apply cost factors to work practices |
Group E
|
Unit code |
Unit title |
|
CUVACD302A |
Produce computer-aided drawings |
|
MSAPMOPS363A |
Organise on-site work |
|
MSAPMPER200C |
Work in accordance with an issued permit |
|
MSAPMSUP390A |
Use structured problem solving tools |
|
MSFFF2006 |
Apply surface coatings by spray gun |
|
MSFFM2012 |
Set up, operate and maintain pressure and clamping machines |
|
MSFFM3001 |
Construct chair and couch frames |
|
MSFFM3003 |
Produce angled and curved furniture using manufactured board |
|
MSFFM3004 |
Produce angled and curved furniture using solid timber |
|
MSFFM3007 |
Prepare and apply decorative surfaces for furniture |
|
MSFFM3008 |
Select timbers for furniture production |
|
MSFFM3009 |
Produce manual and computer-aided production drawings |
|
MSFFM3011 |
Measure and draw site layout for manufactured furniture products |
|
MSFFM3012 |
Set up, operate and maintain sawing machines |
|
MSFFM3013 |
Set up, operate and maintain drilling machines |
|
MSFFM3014 |
Set up, operate and maintain joining machines |
|
MSFFM3015 |
Set up, operate and maintain planing and finishing machines |
|
MSFFM3016 |
Set up, operate and maintain multi-head planing and moulding machines |
|
MSFFM3017 |
Set up, operate and maintain routing and shaping machines |
|
MSFFM3018 |
Set up, operate and maintain mechanical wood-turning lathes |
|
MSFFM3019 |
Set up, operate and maintain automated edge banding machines |
|
MSFFM3020 |
Fabricate synthetic solid surface products |
|
MSFFM3023 |
Produce and maintain cutting tools |
|
MSFFM3024 |
Construct jigs and fixtures |
|
MSFFT4001 |
Coordinate on-site installation of furnishing products |
|
MSFFT4007 |
Sample, inspect and test products to specifications |
|
MSFFT4008 |
Interpret and use workplace information |
|
MSFFT4009 |
Match furnishing style and materials to customer requirements |
|
MSS402001A |
Apply competitive manufacturing practices |
|
MSS402002A |
Sustain process improvements |
|
MSS402010A |
Manage the impact of change on own work |
|
MSS402020A |
Apply quick changeover procedures |
|
MSS402021A |
Apply Just in Time procedures |
|
MSS402040A |
Apply 5S procedures |
|
MSS402050A |
Monitor process capability |
|
MSS402051A |
Apply quality standards |
|
MSS402060A |
Use planning software systems in operations |
|
MSS402061A |
Use SCADA systems in operations |
|
MSS402080A |
Undertake root cause analysis |
|
MSS402081A |
Contribute to the application of a proactive maintenance strategy |
|
TLID2003A |
Handle dangerous goods/hazardous substances |
Group F
Up to five (5) relevant units may be chosen from units not already selected from Groups A to E, or units available in this Training Package or other endorsed Training Packages and accredited courses. Those units must be aligned at Certificate II level (maximum 1 unit), Certificate III level (maximum 5 units) or Certificate IV level (maximum 1 unit).
Units selected from other Training Packages and accredited courses via Group F must be relevant to the qualification outcome and not duplicate units available within this qualification.
Qualification Mapping Information
Supersedes and is based on LMF32109 Certificate III in Cabinet Making. Outcomes are equivalent.
Links
Companion Volume implementation guides are found in VETNet - https://vetnet.gov.au/Pages/TrainingDocs.aspx?q=0601ab95-583a-4e93-b2d4-cfb27b03ed73
