Unit of competency details

Unit descriptor 

This unit of competency specifies the outcomes required to remove graffiti and apply preventative materials to different surfaces to form graffiti-resistant surface systems.

The unit includes planning and preparation for the work, preparation of the work site and materials, removal of graffiti, application of preventative material and completion of clean-up activities.

Application of the unit 

This unit of competency supports the attainment of the understanding and skills to remove graffiti and apply protective coatings, which may include working with others and as a member of a team.

Prerequisite units 

CPCCOHS2001A

Apply OHS requirements, policies and procedures in the construction industry

Employability skills 

This unit contains employability skills.

Elements describe the essential outcomes of a unit of competency.

Performance criteria describe the performance needed to demonstrate achievement of the element. Where bold italicised text is used, further information is detailed in the required skills and knowledge section and the range statement. Assessment of performance is to be consistent with the evidence guide.

ELEMENT 

PERFORMANCE CRITERIA 

1. Plan and prepare.

1.1. Work instructions and operational details are obtained using relevant information , confirmed and applied for planning and preparation  purposes.

1.2. Safety  (OHS ) requirements are followed in accordance with safety plans and policies.

1.3. Signage and barricade requirements are identified and implemented.

1.4. Plant, tools and equipment  are selected to carry out tasks are consistent with the requirements of the job, checked for serviceability and any faults are rectified or reported prior to commencement.

1.5. Materials quantity requirements are calculated in accordance with plans, specifications and quality requirements .

1.6. Materials  appropriate to the work application are identified, obtained, prepared, safely handled and located ready for use.

1.7. Environmental requirements  are identified for the project in accordance with environmental plans and regulatory obligations and applied.

2. Prepare site and materials.

2.1. Site area is set up for graffiti removal and preventative application processes to suit surfaces to be treated.

2.2. Adjoining surfaces to application area are protected by masking off or covering prior to application of graffiti preventative coatings.

2.3. Adequate ventilation is provided for application area.

2.4. Stormwater protection systems are installed where appropriate.

3. Remove graffiti.

3.1. Preparation processes are selected to suit substrate surfaces and graffiti circumstances.

3.2. Type of coating previously used to cover graffiti is identified in accordance with current industry standards of practice, manufacturer recommendations and specifications.

3.3. Graffiti removal processes are applied to affected area in accordance with current industry standards of practice, manufacturer recommendations and specifications.

4. Apply preventative application material.

4.1. Substrate surfaces are cleaned and prepared for preventative application coatings in accordance with current industry standards of practice and manufacturer recommendations.

4.2. Type of preventative coating  to cover specific type of graffiti is identified and prepared in accordance with manufacturer recommendations and job specifications.

4.3. Preventative application coating to cover specific type of graffiti is applied  in accordance with manufacturer recommendations and job specifications.

5. Clean up and store equipment.

5.1. Painting equipment is dismantled, cleaned, maintained and stored in accordance with manufacturer recommendations and standard work practices.

5.2. Unused materials are sealed and stored/stacked in accordance with standard material handling practices and company procedure.

5.3. Work area is cleared and materials disposed of, reused or recycled in accordance with legislation, regulations, codes of practice and job specification.

5.4. Plant, tools and equipment are cleaned, checked, maintained and stored in accordance with manufacturer recommendations and standard work practices.

REQUIRED SKILLS AND KNOWLEDGE 

This section describes the skills and knowledge required for this unit.

Required skills 

Required skills for this unit are:

• communication skills to:

• determine requirements
• enable clear and direct communication, using questioning to identify and confirm requirements, share information, listen and understand
• follow instructions
• read and interpret:

• documentation from a variety of sources
• drawings and specifications

• report faults
• use language and concepts appropriate to cultural differences
• use and interpret non-verbal communication, such as hand signals

• evaluating own actions and making judgments about performance and necessary improvements
• identifying and accurately reporting to appropriate personnel any faults in tools, equipment or materials
• organisational skills, including the ability to plan and set out work
• recognising procedures, following instructions, responding to change and contributing to workplace responsibilities, such as current work site environmental and sustainability frameworks or management systems
• teamwork skills to coordinate own work with others to action tasks and relate to people from a range of cultural and ethnic backgrounds and with varying physical and mental abilities
• technological skills to:

• use a range of mobile technology, such as two-way radio and mobile phones
• voice and hand signals to access and understand site-specific instructions.

Required knowledge 

Required knowledge for this unit is:

• graffiti resistant material technologies and applications
• job safety analysis (JSA) and safe work method statements
• material safety data sheets (MSDS)
• materials storage and environmentally friendly waste management
• painting and decorating terminology
• plans, drawings and specifications
• processes for the calculation of material requirements
• quality requirements
• surface preparation techniques
• types and properties of commonly used graffiti materials
• types, characteristics, uses and limitations of graffiti removal materials
• types, uses, limitations and operating techniques of graffiti removal equipment
• workplace and equipment safety requirements.

EVIDENCE GUIDE 

The evidence guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.

Overview of assessment 

This unit of competency could be assessed in the workplace or a close simulation of the workplace environment, provided that simulated or project-based assessment techniques fully replicate construction workplace conditions, materials, activities, responsibilities and procedures.

Critical aspects for assessment and evidence required to demonstrate competency in this unit 

A person who demonstrates competency in this unit must be able to provide evidence of the ability to:

• locate, interpret and apply relevant information, standards and specifications
• comply with site safety plan and OHS legislation, regulations and codes of practice applicable to workplace operations
• comply with organisational policies and procedures including quality requirements
• safely and effectively operate and use tools, plant and equipment
• communicate and work effectively and safely with others
• remove graffiti from two different substrates of at least 1 square metre using two approved cleaning methods
• apply a minimum of one sacrificial and one non-sacrificial preventative coating, each to a different substrate of at least 1 square metre.

Context of and specific resources for assessment 

This competency is to be assessed using standard and authorised work practices, safety requirements and environmental constraints.

Assessment of essential underpinning knowledge will usually be conducted in an off-site context.

Assessment is to comply with relevant regulatory or Australian standards' requirements.

Resource implications for assessment include:

• an induction procedure and requirement
• realistic tasks or simulated tasks covering the mandatory task requirements
• relevant specifications and work instructions
• tools and equipment appropriate to applying safe work practices
• support materials appropriate to activity
• workplace instructions relating to safe work practices and addressing hazards and emergencies
• material safety data sheets
• research resources, including industry related systems information.

Reasonable adjustments for people with disabilities must be made to assessment processes where required. This could include access to modified equipment and other physical resources, and the provision of appropriate assessment support.

Method of assessment 

Assessment methods must:

• satisfy the endorsed Assessment Guidelines of the Construction, Plumbing and Services Training Package
• include direct observation of tasks in real or simulated work conditions, with questioning to confirm the ability to consistently identify and correctly interpret the essential underpinning knowledge required for practical application
• reinforce the integration of employability skills with workplace tasks and job roles
• confirm that competency is verified and able to be transferred to other circumstances and environments.

Validity and sufficiency of evidence requires that:

• competency will need to be demonstrated over a period of time reflecting the scope of the role and the practical requirements of the workplace
• where the assessment is part of a structured learning experience the evidence collected must relate to a number of performances assessed at different points in time and separated by further learning and practice, with a decision on competency only taken at the point when the assessor has complete confidence in the person's demonstrated ability and applied knowledge
• all assessment that is part of a structured learning experience must include a combination of direct, indirect and supplementary evidence.

Assessment processes and techniques should as far as is practical take into account the language, literacy and numeracy capacity of the candidate in relation to the competency being assessed.

Supplementary evidence of competency may be obtained from relevant authenticated documentation from third parties, such as existing supervisors, team leaders or specialist training staff.

RANGE STATEMENT 

The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.

1.1. Information  includes:

• diagrams or sketches
• instructions issued by authorised organisational or external personnel
• manufacturer specifications and instructions, where specified
• MSDS
• memos
• regulatory and legislative requirements pertaining to the removal of graffiti and application of protective coatings
• relevant Australian standards
• safe work procedures relating to the removal of graffiti and application of protective coatings
• signage
• verbal, written and graphical instructions
• work bulletins
• work schedules, plans and specifications.

1.2. Planning and preparation  include:

• assessment of conditions and hazards
• determination of work requirements and safety plans and policies
• equipment defect identification
• work site inspection.

1.3. Safety  (OHS ) is to be in accordance with state and territory legislation and regulations and project safety plan and may include:

• emergency procedures, including extinguishing fires, organisational first aid requirements and evacuation
• handling activities that may require the assistance of others or the use of manual or mechanical lifting devices where size, weight or other issues, such as a disability are a factor
• hazard control
• hazardous materials and substances
• organisational first aid
• PPE prescribed under legislation, regulations and workplace policies and practices
• safe operating procedures, including the conduct of operational risk assessment and treatments associated with:

• earth leakage boxes
• electrical and fire and/or explosion from combustible materials
• falling objects
• lighting
• manual handling
• power cables, including overhead service trays, cables and conduits
• restricted access barriers
• solvents, lead, chemicals, fumes/gases
• surrounding structures
• traffic control
• trip hazards
• work access platforms
• work site visitors and the public
• working at heights
• working in confined spaces
• working in proximity to others, work site visitors and the public

• use of firefighting equipment
• use of tools and equipment
• workplace environmental requirements and safety.

1.4. Tools and equipment  include:

• airless spray equipment
• brushes
• mobile scaffold
• planks
• rollers
• scrapers
• stepladders
• trestles
• vacuum cleaners
• water blasters.

1.5. Quality requirements  include:

• internal company quality policy and standards
• manufacturer specifications, where specified
• relevant regulations, including Australian standards
• workplace operations and procedures.

1.6. Materials  include:

• solvents
• cleaning materials.

1.7. Environmental requirements  include:

• clean-up management
• dust and noise
• stormwater protection
• waste management.

1.8. Preventative coatings :

• include:

• sacrificial
• non sacrificial

• may include:

• siliconised
• other types.

1.9. Application :

• systems include:

• brush/roller
• spray

• is to conform with relevant Australian standard.

Unit sector 

Construction

Functional area